Neutral Density Filters

Are you familiar with neutral density filters? Click through to read about what type of photographs I like to take using neutral density filters and the physics behind the large colour cast of very opaque high ND filters.

 

---

 

As you might already know, neutral density (ND) filters are used both in physics and in photography to reduce the amount of light reaching the detector. In my physics PhD research I use them when the laser is too strong, and in photography I use them when I want to capture longer exposures. But how much do they reduce the amount of light that goes through? That depends on their optical density. Optical density (OD) is a measure of how absorbent the filter is and it is defined as the negative of the logarithm (base 10) of the transmission. Where the transmission is the ratio between the transmitted (It) and the incident (I0) light, and it varies between 0 and 1.

Note: When talking about neutral density filters, optical density (OD) and neutral density (ND) are the same thing.

From this equation follows that, the larger the ND the less light that gets transmitted through the filter. If we look at a few particular cases of interest we see that for ND = 0 (no filter), 100% of the light is transmitted. For ND = 0.3, 50% of the light is transmitted through the filter (the light is reduced by 1 stop). For ND = 0.6, 25% of the light is transmitted through the filter (the light is reduced by 2 stops). And for ND = 3, one thousandth of the light (0.1%) is transmitted through the filter (the light is reduced by 10 stops). In the table below you will find a summary of these numbers. I have highlighted the cases I will be focusing on during this post :)

It is important to note that when stacking ND filters their strength just adds up. So if you are using an ND 0.3 filter plus an ND 0.6 filter, that is the same as using a single ND 0.9 filter!

Note: If you, like me, were wondering what exactly is a stop and why is it such a widespread measure of light in photography, you might like to check out this enlightening post by Photography Mad, in which he explains that “a stop is doubling or halving the amount of light let in when taking a photo”. From what we’ve just seen about neutral density, 1 stop of light reduction is equivalent to ND 0.3.

I myself own two ND filters for my photography. I have a lighter one of ND = 0.6 (2 stops) and a much much darker one of ND = 3 (10 stops), both are B+W brand. I rarely use the ND 0.6, but I did use it recently when I was out in Portland with my friend and photographer Brian Bonhan shooting waterfalls. I found that I wanted a little bit of a longer exposure time to smoothen the water  in the photograph but not a huge amount more, hence the combination of a polariser filter plus an ND 0.6 was perfect!

Here below you can see one of the images I captured with the sun rays at Abiqua Falls. To be totally honest, I can’t remember if I used the ND 0.6 in that particular shot or not as I kept taking it on and off the camera the whole day, but you get the picture of the smooth water anyway! hehe :)

Sun Rays at Abiqua Falls

As I’ve just mentioned, I don’t use the ND 0.6 very often because it does not increase the exposure time by that much. However, the ND 3 (10 stops) filter allows for very very very long exposure times, even in broad daylight!! This filter lets through only about one thousandth of the light, that is 0.1%!! Hence I was able to shoot the San Francisco Golden Gate from Baker Beach at 3pm in the afternoon and get a 25 second exposure! In the animation below you can see the difference between using the ND 3 filter or not. Both images are straight out of camera, with the same white balance settings.

As you might have noticed, not only does the water get smoother, but the overall colour of the image also changes. This is known as the “colour cast” that the neutral density filter inflicts on the image. Depending on how strong your ND filter is, and who the manufacturer is, this colour cast will be stronger or weaker, and of one colour or another. The Digital Picture has a wonderfully in-depth comparison of the characteristics of 10 stop ND filters from different manufacturers, I recommend you check it out when you have some time :)

Fortunately, in the ND 3 filter I own, the colour cast is not a huge deal, and I can easily remove it in post processing if I want to, which is what I did for this Golden Gate long exposure from Baker Beach

However, I don’t always want to remove the colour cast. In fact, I often find that I like the version with the long exposure and colour cast better. I like the redish tinge acquired by the photograph and I often choose to exaggerate the colour cast instead of removing it. That is what I did with this image below of the Basilica Del Pilar in my hometown of Zaragoza, Spain. In the animation you can see the shots straight out of the camera (no editing at all) both with and without the ND filter.

I ended up preferring the one with the ND 3 filter and bumped up the colours in post processing because, why not? Because I could, and because I wanted to :) I like the result!

Basilica Del Pilar at Sunset

About half an hour after this shot, the sun was below the horizon and the buildings in the city started lighting up, including the basilica. I kept on taking pictures from my vantage point on the Puente de Piedra and kept on trying with and without ND filter. Here is the result, straight out of the camera:

In this case the chosen image was the one without the ND filter, and once again I decided to enhance the colours to these lovely blues.

Basilica Del Pilar during Blue Hour

So now that I’ve talked a little bit about how I like to use my ND filters, lets get down to the physics. More specifically, what are ND filters made out of, and why do the high ND filters present a distinct colour cast? 

It is my understanding that ND filters have traditionally been made out of resin, and that recently companies have started making them out of coated glass instead, which is said to reduce the colour cast. Formatt Hitech writes about their Firecast ND coating:

“FirecrestND is a quantum leap improvement over all previous generation ND and IRND products and represents the technological state of the art in scientific light modification. Firecrest is a radical departure in how ND filters are manufactured. Previous generation NDs were made by dying resin. Firecrest is not a dying process. Rather, Firecrest is a carbon metallic multicoating process that is applied directly to the glass through an electrolytic process.”

Let’s look more in detail at the colour cast of my B+W ND 3 (10 stops) filter. If the overall colour of the image is affected by the ND filter, that must mean that light of all wavelengths is not attenuated equally. With that in mind, I took my two ND filters down to the lab and measured their transmission spectra. In order to do so I used a spectrometer, which separates light into different wavelengths, and then for each wavelength calculates the amount of light transmitted through the sample, in this case, the ND filter.

In the graph below you can see the result of each measurement. In blue I show the amount of light transmitted when not using any filters (100%, of course!). The red curve depicts the amount of light transmitted through the B+W ND 0.6 (2 stops) filter. And finally, the green curve shows the amount of light transmitted through the B+W ND 3 (10 stops) filter. Cameras typically capture light from about 400 nm to 750 nm, which I have shaded with the corresponding colours.

Here below, you can see the features of each filter magnified when plotted on a logarithmic scale. Thanks to Martin Heller for the suggestion of using the log scale! Being the physicist I am and using log scales all the time I can’t believe it hadn’t occurred to me! But that’s what feedback from the readers is for :) hehe

Firstly, let’s have a closer look at the ND 0.6 transmission curve. We can see that the transmission spectra is not flat, and if we average out the values for the range between 400 nm and 750 nm we get an overall transmission of 28%. This is very close to the 25% transmission that corresponds to an ND 0.6 (2 stops) filter, so that’s good! It is always nice when experiments are in agreement with our expectations hehe.

From these graphs it is hard to discern what the spectra of the ND 3 (10 stops) filter looks like, so let’s zoom in and see!

Similarly to the ND 0.6, this ND 3 does not have a flat transmission spectra. If we average the percentage of transmitted light from 400 nm to 750 nm we get a value of 0.18%, which is of the same order of magnitude as the expected value of 0.1% transmission for an ND 3 filter.

However, there is a very large difference between these two filters. Whereas with the ND 0.6, the transmission in the infra red region was smaller than that of the visible region, in this ND 3 filter, the infra red light (and a bit of the red light too) is transmitted with much more intensity through the filter, than the rest of the visible light.

Now comes into play the fact that camera sensors can actually detect IR light, except that they normally also have an IR high-pass filter designed to prevent the IR light from reaching the sensor. Otherwise the IR light would pollute the visible light and affect the RBG sensor. If what you want is to take IR photos, then you can convert a DSLR by removing this IR  high-pass filter, you can read about how to do that in this post by Extreme Tech. However, if what you want is to take a long exposure shot with this ND 3 filter, you are going to find that this “excess” of red and infra red light, manifests itself as a redish colour cast like I have shown you in my photographs.

Now, the million dollar question? What makes ND filters from different brands have different colour casts? Well, that I am not too sure of. I suspect that if they use different materials their transmission spectra would be different, but since I don’t have filters from any other brands I haven’t been able to measure them. I have looked online for the specification sheets of these photography high ND filters, but have come up empty handed. However, I have found transmission spectra for ND filters manufactured by Thorlabs. This is the brand we use in our research lab, and I must say, they look pretty similar to the B+W transmission spectra I have just shown you!

And finally, to finish off this post about neutral density filters, I would like to point out that they can be used for other different effects in photography, besides smoothing water. Another very common advantage of having longer exposures is the ability to capture the movement in the clouds. This is what I did one morning at sunrise at Uluru.

In this situation I liked the streaks the clouds formed in the long exposure shot using the ND 3 filter, and only did some minor adjustments in the post processing of the image. Here is the result:

Sunrise at Uluru

With this we come to the end of this post. I hope you have enjoyed it and learnt some interesting facts about the use of neutral density filters in photography and the physics behind their colour cast.

Thank you for reading! :)

xx Ana :)